Jacuzzi whirlpool manual

Use the provided latex glove to handle the UV bulb. An original technology that releases all the sensations and beneficial effects of water with extreme simplicity.

To view our warranty cards, please click here. Our collection of hot tubs and bathroom products are available for sale across the UK through our exclusive Jacuzzi retailer network. Wait for 5 minutes and assure no water is dripping. If you are only replacing the UV bulb and NOT cleaning the quartz tube then the hot tub does not need to be drained. It is also necessary to monitor and maintain the proper chemical treatment of the spa water to avoid algae, bacterial and other hazards. Below we give closer views of key operating controls and parts of this hot tub or spa installation.

We are a wholesale distributor of spa and hot tub parts. When Jacuzzi, Inc reorganized their company in , they moved their spa production to their Sundance plant. We continue to and are still servicing Jacuzzi Hot Tubs as a service center. Discover the current Jacuzzi promotions and find the perfect bath or hot tub for sale. They will be best placed to advise you as they will be experienced in managing water in your area. Watch out: exposed electrical splices or connections can kill someone.

Please note — for the above products you will need a push fit hose adaptor to be able to connect your hosepipe. Warning: do not use abrasive cleaners as they can scratch the quartz tube surface.

Dropin undermount for extended use exceeding minutes and for young children. A solid red light indicates that the UV bulb is activated. High speed will be obvious because the pump noise will increase and the visible flow of water exiting the jets in the tub will be stronger.

You can purchase these from our authorised Jacuzzi dealerships or other DIY retailers. Most of our local authorised dealerships offer hot tub moving services. The filter is filled with water and air is bled from it after the pump has been started. Being wet, naked, and standing on a wet floor is a good preparation for electrocuting yourself.

Consult a licensed electrician if repairs are needed. We have also included them below. There are a variety of codes that may appear on your hot tub display panel and the code shown will change the action required. This spa was installed ca and is still in operation.

Instructions for changing your ClearRay bulb can be found in the packaging of your new bulb. This particular spa operates at a chlorine level of 1 to 1. Whirlpool operating instructions. We have no relationship with advertisers, products, or services discussed at this website. Regular testing every days is needed. Typical instructions require filling the spa and pump filter or strainer assembly with water before turning on the pump. Once the spa has been removed from the carton and before it is permanently installed , check the spa completely for damage.

Fill the shell with water and operate the system refer to Operating Instructions to check for leaks which may have resulted from improper shipping or handling. All Jacuzzi Whirlpool Bath spas are factory tested for proper operation and water tight connections prior to shipment. If leaks or other problems are detected, immediately notify your Jacuzzi Whirlpool Bath dealer, Authorized Service Agent, or call Jacuzzi Whirlpool Bath, , or NOTE: Damage or defects which could have been discovered and repaired prior to installation and which are claimed after final installation of the spa, are excluded from our warranty.

Because your spa is portable, you can locate it just about anywhere you wish—on a deck, patio, or even indoors. Just be sure to position it above ground in an area with good drainage and on a level, continuous surface which can support the weight of the spa when filled with water and people. See specifications sheet for minimum service access requirements. Your spa requires a VAC, 50 AMP, 4-wire, grounded type GFCI protected electrical service with copper conductors, and must be in a separate circuit having no other appliance connected in that circuit.

If you do not have this kind of circuit, a qualified electrician should install the necessary wiring. The circuit must also have a ground wire in order to take advantage of the designed-in safety features of the spa.

A bond wire must also be used. Bond according to procedure described on the next page. Danger: Without proper grounding and bonding, a system malfunction may cause fatal schock. CAUTION: Do NOT apply electrical power to the spa unless it is filled with water to the normal water level, which is approximately 7" below the spa rim refer to location of water level indicator on face of skimmer.

Not heeding this caution will nullify the warranty. In addition to damaging the unit, operating the unit with insufficient water could cause a fire. Do NOT locate lighting fixtures directly above the spa; lighting and electrical receptacles must be located at least 5 feet from the spa.

Lighting located between 5 and 10 feet from the spa must be on a circuit protected by a GFCI. Refer to National Electrical Code, Do NOT use electrically connected devices, such as television, radio, telephones, stereo speakers, light or cooking devices within 5 feet of the spa when the spa is being used. An approved ground may be an 8 foot long ground rod, a plate electrode, or a buried metal water pipe with at least 10 feet of buried pipe. Check your local building code for requirements.

Bonding lugs are available at your local electrical supply store. Bond bar location is shown below. If you install the spa outdoors, we recommend that you provide a concrete pad for it to rest on. To do this, construct forms for a 4" thick level pad. Install a 10 gauge wire mesh 6" x 6" steel reinforced grid.

Attach a 8 solid copper wire to the grid with a ground clamp. This wire should be long enough to reach the bond bar on the spa electrical cabinet minimum 36" , but should NOT be located under the base of the spa. Then pour the concrete pad. Whether you install your spa indoors or outdoors, you can drain it completely by attaching a garden hose to the hose bibb drain valve located on the suction plumbing of the spa.

Simply run the hose to the house sewer line or drain field and open the hose bibb. Make sure the area surrounding the spa has good drainage to keep water from collecting at the base of the spa—especially near the equipment area. Refer to illustration below. Good drainage must be provided and proper waterproof building materials must be used in the area surrounding and beneath the spa. Take into consideration that high room humidity will exist due to high spa water temperatures.

Providing natural or forced ventilation of the room will help maintain comfort and minimize moisture damage to the building. Jacuzzi Whirlpool Bath is not responsible for damages resulting from excess moisture or water spillage. Consult an architect or engineer for aid in designing your indoor installation. Remove the plastic sheet covering the spa. Remove any packing materials from the spa. Remove the filter cartridge from its plastic bag. Clean the interior of the spa of any remaining construction debris.

Remove stubborn stains, paint, or tar with turpentine, isopropyl alcohol or paint thinner. A mild liquid dishwashing detergent on a damp cloth is fine for cleaning off other dirt. Plaster can be removed by scraping with a soft plastic or wooden edge. Install the skirt panels which were not installed on the spa at the factory. Use the screws provided in your spa accessory package and follow instructions provided with the panels.

On initial start-up, it is necessary to purge and sanitize the system as stated below. Besides being a beautiful addition to your indoor decor or outdoor landscaping, your Jacuzzi Whirlpool Bath spa will provide you with the ultimate in spa pleasure.

Familiarize yourself with the operation of the electronic control panel, as described on pages of this manual. Access under the spa behind the skirts is required only to drain the water. Refer to water line indicator mark on skimmer frame. Whenever the power is ON, the system may activate even though no controls are operated.

In addition to damaging the unit, operating the spa with insufficient water could cause a fire. Refer to information on using the Water Rainbow spout if desired. Make sure there is no other appliance on that circuit. The spa will automatically begin to operate when electrical power is applied.

During each filter cycle, the spa will heat to the set temperature. Control of temperature, jets, blower and spa light is readily accessible from within the spa. The current temperature is constantly shown on the display. Press either or once to display the set temperature. The set temperature is designated by a triangle on the left side of the display.

Each time either button is pressed again, the set temperature will increase or decrease depending upon which button is pressed. After 3 seconds, the display will automatically show the current spa temperature. Press any button to reset the system in the rare instance of an overheat condition. Press the button again for the highspeed jet operation, and again to deactivate the jets. The low-speed jet operation will start automatically when the heater is turned on or when a filter cycle is activated.

When a freeze condition is detected, high speed jets are automatically activated. Whenever the low-speed is energized with this button, it will automatically turn off after 4 hours of operation. The high-speed automatically turns OFF after 30 minutes. The button starts and stops the blower for aeration in the spa. Welcome to ManualMachine. We have sent a verification link to to complete your registration.

Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Whirlpool Spa. If your spa product does not have a thermometer, we recommend that you use a medical clinical type thermometer for an accurate measurement of spa water temperatures.

Contact your Dealer for replacement cover if broken or missing. The wet surface of the spa is slippery. Use care when entering and exiting. If leaks or other problems are detected, immediately notify your Jacuzzi Whirlpool Bath dealer, Authorized Service Agent, or call Jacuzzi Whirlpool Bath, , or for Warranty Service.