Datalogic scanners manual

QBT, kit, document handling, Inc. Documentation kits 93acc sw-docs-test chart for matrix fam. The company does it answer your question? Using advanced imaging technology, enhance-ment or as well. Website or provided on appropriate media. Using advanced imaging technology, the Gryphon GFS 2D fixed mount bar code reader provides a complete self-contained solution for OEM use into self-service kiosks, price. The Datalogic Gryphon user manual online. If you visit our website and would like to make comments or suggestions about this or other Datalogic publications, please let us know via the Contact Datalogic page.

With Datalogic s patented Green Spot technology. For more information plus a complete listing of available symbology types, turn to the Symbologies chapter of this manual. The linear imager is factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide.

In the programming chapters, factory default settings are indicated with bold text and yellow highlighting. These defaults represent the settings for the RS standard interface. For a listing of defaults for other interfaces, reference Chapter D, Default Settings , in the section titled Interface Default Exceptions. Scan the two bar codes below to reset the imager handheld and Base Station to factory settings.

The following features and descriptions apply only to Bluetooth BT models of the imager. Connect power to the Base Station. To ensure the Base Station is unlinked from any other imagers, press the button located on its bottom side for three seconds. Place the imager in the Base Station for one minute to get a small charge in the battery. Read the label on the Base Station with the imager.

The imager will sound a good read beep and the LED will flash amber. Replace the imager in the Base Station to continue the charge.

Once an imager is linked to a Base Station, they will remain linked until specific action is taken to unlink them see Unlinking. They will remain linked if the Base Station is unplugged, if the battery is removed from the imager or if the entire charge is used up, and if the imager is taken out of range of the Base Station. Under normal operation, scanning of the link label will only be required once in the life of the product. It will also place the imager in Sleep Mode.

If the bar code is read when the imager is out of range of its linked Base Station, the imager will unlink, but the Base Station will remain linked to the imager and will not allow another imager to be linked to it until the unlink button is pressed, the original imager is brought in range, linked, and then unlinked again. Push the button on the bottom of the Base Station — Pushing the button on the Base Station while the imager is in range will break the link between the devices. If the button is pushed while the imager is out of range, the Base Station will unlink and make itself available to other imagers.

The imager will not automatically break its link with the Base Station, but can be linked to any other Base Station by reading its link label. Scan the link label on an alternate Base Station — Scanning the link label on a Base Station with an imager that is linked with another Base Station will drop the link between the original pair and establish a link between the imager and the new Base Station.

If the new link is performed within range of the old Base Station, it is free to establish a link to the next imager that reads its link label. If it is done outside the range of the old Base Station, it retains its old link and will not allow a new imager to link to it until its unlink button is pressed. The imager contains a mAh Lithium-Ion rechargeable battery. A fully charged battery will provide up to 12, scans over a 12 hour period. Actual charge life on the imager will depend on the configuration of the how the imager is configured via the programable features in this manual; in particular, Deep Sleep Mode and Leash Alarm settings can impact battery life.

When the imager is placed in the Base Station, the battery will automatically charge. While charging is taking place, the charging LED marked with a battery symbol will blink green. When the battery is fully charged, the charging LED will stay on a solid green.

If there is an error in charging either with a failure in the charging circuit or with a failure of the battery, the charging LED will flash red.

When this happens, the battery should be replaced. If the imager is misplaced in the area around the Base Station, it can be located by momentarily pressing the button on the bottom of the Base Station.

When the button is momentarily pressed, a message is sent to the imager instructing it to sound a series of six short beeps. The Double Read Timeout feature sets a time limit that determines how much time must pass before reading the same label again e. The Imager Timeout feature sets the time for automatically switching the unit off when the imager is not in use. This feature specifies the state of the green scanner LED when the scanner is idle and ready to read a label.

Options are:. Choices are:. Adjusts the good read beep to sound at a selectable low, medium or high frequency, selectable from the list below. Selects the beeper volume loudness upon a good read beep. There are five selectable volumes, with each volume increment adding approximately five decibels to the previous level.

Pressing the trigger activates scanning; releasing it stops scanning. Pressing the trigger activates scanning; pressing it a second time stops scanning.

When this feature is set to ON while in stand mode, the illumination LEDs go to a dim state after a timeout of reading no labels. In both cases, the illumination LEDs come back on when something passes in front of the imager. Limits the time following pressing the trigger that the illumination LED aiming light is lit.

Disabling this feature turns the illumination off. Global minimum length can be set to qualify data entry. The length is defined as the actual bar code data length to be sent. Ensure that the mini- mum-length setting is no greater than the maximum-length setting; otherwise, the labels of the symbology will not be readable. In particular, you can set the same value for both minimum and maximum lengths to force decoding of only fixed-length bar codes.

This setting has no effect on certain symbologies of fixed length. Global maximum length can be set to qualify data entry. At the time of this writing, the Imager supports the interfaces listed in Table Select the desired interface type from the table, then reference the page number given for the customizable features section associated with each interface. Consult Table for more information regarding keyboard wedge interface types. The correct interface cable is included for the imager interface type you ordered.

While the CTS line is inactive, the imager remains in a host-disabled state; following a successful label transmission, the CTS signal must transition to inactive and then to active to enable scanning for the next label.

This delay is inserted after each data character transmitted. If the transmission speed is too high, the system may not be able to receive all characters. You may need to adjust the delay to make the system work properly. When enabled, this feature passes all data through the imager to the host as it comes in. If, for example, one of the devices in the chain is a terminal where someone is entering data while another person is simultaneously scanning a bar code requiring transmission to the host, the scanner will wait for the RS channel to be quiet for a specified period of time set via RS Host Echo Quiet Interval.

The scanner can be set to observe this delay before sending its data in order to avoid RS transmission conflicts. This setting specifies the time interval of RS channel inactivity which must transpire before the imager will break the host echo loop to transmit the bar code data that has just been scanned to the host. Welcome to ManualMachine. To arrange for a Software Maintenance and Support Agreement please contact your Datalogic sales person. Follow the steps below to connect and get your reader up and communicating with its host.

Connecting the Base Station. Configure Other Settings if not using factory settings for that interface. Datalogic recommends annual replacement of rechargeable battery packs to ensure.

In the event the battery pack leaks and the fluid gets into your eye, do not rub the eye. Rinse well with water and immediately seek medical care. If left untreated, the battery fluid could cause damage to the eye.

Use only the authorized power supplies, battery pack, chargers, and docks supplied by your Datalogic reseller. Do not disassemble or modify the battery. The battery contains safety and protection devices, which, if damaged, may cause the battery to generate heat, explode or ignite.

Do not place the battery in or near fire, on stoves or other high temperature locations. Do not place the battery in direct sunlight, or use or store the battery inside cars in hot weather. Doing so may cause the battery to generate heat, explode or ignite.

Using the battery in this manner may also result in a loss of performance and a shortened life expectancy. Do not place the battery in microwave ovens, high-pres- sure containers or on induction cookware. Immediately discontinue use of the battery if, while using, charging or storing the battery, the battery emits an unusual smell, feels hot, changes color or shape, or appears abnormal in any other way. Do not use the battery pack if it is damaged in any part. Battery pack usage by children should be supervised.

As with other types of batteries, Lithium-Ion LI batteries will lose capacity over time. Capacity deterioration is noticeable after one year of service whether the battery is in use or not. It is difficult to precisely predict the finite life of a LI battery, but cell manufacturers rate them at charge cycles. The typical manufacturer advertised useful life of LI batteries is one to three years, depending on usage and number of charges, etc.

For most applications, batteries should be replaced after one year of service to maintain customer satisfaction and minimize safety concerns. With a screwdriver, unscrew the battery cover screw. Unplug the three screws securing the battery holder, and unplug the white connector.

Carefully lift out the gold contacts circuit, and remove the battery holder while letting the white connector pass through the hole in the battery holder as shown in the picture below. Remove the old battery from its place if present , and insert the new battery in the same position. Replace the battery holder, plug in the connector and return the contacts circuit to its previous location. When inserting the new battery into the handle, take care to position the battery and the connector as shown.

Insert the cover in the handle and screw it back into place. The base station is configured by installing one of two sets of mechanical parts that come with the cordless kit.

Use the other mounts only for horizontal mounting, with lower retention of the scanner. The different parts may be interchanged to customize retention preferences. A tool such as a rigid pen or a flat screwdriver can be used to change the mounts. Do not allow it to touch the contacts. Insert the appropriate parts for the desired base station position, as shown below. Welcome to ManualMachine.

We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Datalogic Scanning. Datalogic Scanning, Inc. Disclaimer Datalogic has taken reasonable measures to provide information in this manual that is complete and accurate, however, Datalogic reserves the right to change any specification at any time without prior notice.

Patents Design Pat. One or more of the values entered is not permitted. Please wait while we process your request. This process can take several minutes depending on the number of warranties being checked.

Select registration option. Error: Javascript is disabled in this browser. This page requires Javascript. Modify your browser's settings to allow Javascript to execute. See your browser's documentation for specific instructions. HP Customer Support. Select your model. How does HP install software and gather data? Search all support. Search help. Tips for better search results Ensure correct spelling and spacing - Examples: "paper jam" Use product model name: - Examples: laserjet pro p, DeskJet For HP products a product number.

Loading Results. Apache Log4j Update Please see this document here for current information regarding the Apache Log4j vulnerability. Need Windows 11 help?