Be careful not to cut or dig any wood out with the cane. Once all of the spline and cane have been removed, clean the glue out of the corners of the inset with a putty knife. Clean the remaining glue off the inset in the frame and the spline channel. Use a putty scraper or to steel wool to remove the softened glue. An avid perennial gardener and old house owner, Laura Reynolds has had careers in teaching and juvenile justice.

A retired municipal judgem Reynolds holds a degree in communications from Northern Illinois University. Her six children and stepchildren served as subjects of editorials during her tenure as a local newspaper editor. Tweezers will be able to slide between the patch and your item and grip the patch well. If you don't have tweezers, slip a butter knife between the patch and your item.

Lift up to start the patch and remove the rest of it with your fingers. If the patch is large, you may have to make a few passes with the iron. Peel up large patches section by section. Method 2. Purchase a fabric-safe adhesive remover. Glue removers that are xylene or orange oil-based work well.

Pick a liquid-based product able to soak through fabric. An adhesive remover that comes in a spray bottle will be much easier to work with for this purpose.

Rubbing alcohol can also be an effective alternative. Patch test your clothing. Even if the adhesive remover is advertised as fabric safe, it is still possible that it may stain your particular item. You will need to test it out first before using the remover on a patch. Do this over a clean sink to avoid making a mess. Find a small, inconspicuous area on your item that is not easily visible during normal use.

For example, the inside back bottom edge of a hat or jacket would be a good choice. Dab a small amount of adhesive remover onto this spot. Work the adhesive remover into the fabric using your fingers or a clean rag.

Rinse off the adhesive remover and check for discoloration. Expose the area underneath the patch. If your item is a T-shirt, a hat, or a pair of paints, turn it inside out. You will need to access the fabric that is bonded to the patch. If your item is a canvas bag, simply lay it out flat upside-down. Apply your adhesive remover. Squirt or pour the glue remover liberally on the back of the cloth.

Use enough that is soaks through your item completely. Make sure you cover the whole area behind the patch. Work the remover into the fabric using either your fingers or a clean rag. Wait about one minute for the remover to loosen the patch.

Peel off the patch. The adhesive remover should successfully soften the glue, making it sticky. The patch should now easily come off your item. Turn the item right-side-out. Hold it with one hand. Grip the edge of the patch between the index finger and thumb of your other hand. Pull back to lift the edge of the patch up and off your item. Work your way around the patch until it has been entirely peeled away. Repeat on any stubborn areas. If part of the patch is still stuck to your item, try repeating the process, focusing on the spots where the adhesive did not soften properly.

Reapply the adhesive remover however many times it takes to completely remove the patch. However, if the glue remover you used has not softened the adhesive at all, you will likely need to try a different one. If you don't plan on keeping the patch, trim off what you've already peeled off with a pair of scissors.

This will make it much easier to work with and keep the patch from sticking back onto your item. Method 3. Check for stains. The glue from your patch will likely leave a residue behind. If the area where your patch was is now discolored or sticky, you will need to take further action to make your item looking clean and like new again.

If you used the adhesive remover method, launder your item first. This may remove the adhesive completely on its own. Apply adhesive remover directly to the residue. Squirt or pour more adhesive remover onto the patch. Massage it in using your fingers or a clean rag. Allow it to work for approximately one minute.

You can also make your own adhesive remover at home. Just mix two parts baking soda with one part coconut oil and a few drops of orange essential oil. It is a thick paste that is unable to easily soak through fabrics. Launder your item as usual. Simply wash your item using whatever method you normally would. Do this as soon as possible to remove the solvent in case it may damage your item over time. If the item is machine wash safe, go ahead and throw it into your washing machine with a normal load of laundry.

Hand soak delicate items using cold or room temperature water with a small amount of detergent. If the glue seems especially stuck-on, try scrubbing it with a soft toothbrush after the adhesive remover has been worked in.

Apply some liquid laundry detergent directly to the residue patch as a pre-treatment. It should look different, and the scratch may have been removed. Try grit, for instance, and follow the same procedure as before. Make sure to wet the sandpaper each time, and to work gently. Polish the area. Once the scratch is fully removed, polishing the area will make everything look like new. Get some commercial plastic or acrylic polishing compound and place some on a clean cloth. Wipe the whole plastic area to blend everything in.

Then take a clean cloth and wipe off the excess. Method 3. Clean the scratch area. Use a damp cloth dipped into warm water mixed with mild detergent. Rub the cloth over the scratch and surrounding area to remove any dirt and grime. Get a buffer pad and buffing compound. These supplies can be found at hardware stores, and some auto supply stores.

The buffer pad can be attached to any regular electric drill. The buffing compound helps it rub out the scratch. Rub the scratch out by using a drill and buffing pad. Attach the buffing pad to an electric drill. Apply a small amount of buffing compound to the pad follow the instructions on the product. Turn the drill on and gently work the pad over the entire scratch area. Use a touch-up pen, if necessary. If the scratch is deep, a touch up pen will hide the problem further. Find the matching touch-up pen at an auto supply store.

Let the area dry before continuing. Apply clear coat to the area. Clear coat helps blend the buffed area back in with the rest of the plastic. Follow the instructions provided with the product. Work in a well-ventilated area. Polish the area with car wax. Use a clean cloth or polishing pad, and buff the entire area with wax. This final step will help make your car look as good as new.

Jon Gholian Cleaning Specialist. Jon Gholian. You can mix some dish soap in warm water. Dampen a cloth with it and clean the plastic. Then wipe it with a microfiber towel. Not Helpful 0 Helpful 0. It is possible to remove scratches from a plastic screen, provided they are not too deep. Some ways to remove scratches from a plastic screen include: wiping with a Magic Eraser, using a specifically designed commercial scratch remover, rubbing with a pencil eraser or polishing with car headlight cream.

Not Helpful 6 Helpful You can remove scratches from acrylic by polishing. Follow the instructions outlined above in the article for sanding and polishing to remove the scratches. If the scratches are deeper than 5mm, it may not be possible to polish out the scratches. If the item is valuable, it's best to talk to an expert such as a car repairer to find out whether other options exist.

Not Helpful 2 Helpful 2. It may be possible to remove lens scratches provided they are not too deep. Begin by cleaning the lenses gently first, then apply a suitable scratch remover, such as a paste made from baking soda and water. This paste is best applied by rubbing on in a circular motion, using cotton wool.

Gently wipe off and check to see if the scratches have improved. You can also try a scratch-filling product. For more detailed help on removing scratches from plastic lenses, see: How to Remove Scratches from Plastic Lens Glasses.